The New Stuff


Jelly Bean OTA Leak for Galaxy Note 10.1 – Installation

New hottest Samsung device in the town to get an official Android 4.1.1 Jelly Bean update is Samsung Galaxy Note 10.1, the update is currently available for the Galaxy Note 10.1 Wi-Fi 3G model number N8000, Samsung will roll out the update through OTA soon in near future, however folks over Sam Mobile told us that Samsung has just leaked Jelly Bean Android 4.1.1 for the Galaxy Note 10.1 in India, it’s just a test build and is available for manual installation.

As most of you already know well that Jelly Bean comes with number of new apps and features such as Google Now app, advanced notification, smarter keyboard and more, the firmware improvements are also impressive like improve S Note, S Note Widget, calendar colors, Screenshot, text selection and more. It also adds blocking mode, text-message backgrounds and some new multi-tasking features.

As I said mentioned above Samsung hasn’t roll out the update yet but those of you who really want to taste Jelly Bea before OTA release, can install this leaked update manually. It’s important to keep in mind that since it’s just a pre-release, it may contains some bugs and it might not be fully stable for daily drive.

Take a look at below guide to install the leak OTA Android 4.1.1 Jelly Bean N8000DDALI1 update on Samsung Galaxy Note 10.1 N8000. Be sure to make a make a backup of your device data such as SMS, internet setting, contacts music files etc because the below procedure may wipe data, you can sync your contacts with Gmail account and for messages use SMS apps, lastly use file expert app to backup apps.

DISCLAIMER: Please proceed the below guide at your own risk, Android Egis will not be held responsible if your device lost data or get damaged following this guide.


Step #1: Your Galaxy Note 10.1 must be running Android 4.0.4 N8000DDALH1 firmware, check your device firmware information from Setting>About Device. If you’re already on N8000DDALH1 version, skip step 1 to step 10 but not then you need to install it manually, to do so, first of all download the N8000DDALH1 from here or here (Note: Use a Windows PC and USB drivers also should be installed on your PC, you can download 32 bit (x86) Windows from here and 64-bit (x64) Windows from here).

Step #2: Unzip the downloaded file into a folder on PC, you’ll get N8000DDALH1_N8000ODDALH2_N8000DDLG5_HOME.tar.md5 file.

Step #3: Now download the required Odin file to your PC.

Step #4: Extract the Odin file on your PC. .

Step #5: Run the run Odin 3.04.exe you obtained in previous step.

Step #6: Turn off your Galaxy Note 10.1.

Step #7: Reboot the device into download mode by holding down volume down and power buttons, when a warning screen appear, leave both buttons and press volume up button to enter in download mode.

Step #8: Once you’re in download mode plug the device to PC using USB cable. Odin will detect the device, ID:COM will turn yellow/blue and a message saying ADDED will appear. (Note: If Odin doesn’t detect the device, make sure that USB drivers are properly installed on your computer).

Step #9: Click on PDA Button and locate N8000DDALH1_N8000ODDALH2_N8000DDLG5_HOME.tar.md5 from the folder where you’ve unzipped above files in the step 2. (Note: Don’t make any change, just make sure that re-partition is unchecked).

Step #10: Click on Start button to start installation, once the installation done, your device will reboot itself and you’ll see message saying PASS (Note: If Odin refuse to install the update and show message FAIL, or get stuck, close the Odin and unplug device, then pull out battery from the device for a few seconds. Then put the battery back to the device and reboot into download mode. Then install the firmware again.

Step #11: Now download leaked OTA Android 4.1.1 Jelly Bean DDALI1 OTA Update (

Step #12: Place the downloaded OTA update .zip file to your device’s external SD card.

Step #13: Reboot your phone into stock recovery mode by holding down power button and volume up button.

Step #14: Select Apply update from External Storage, then locate the OTA update .zip file ( to start the installation.

Step #15: Once the installation is done, you need to perform wipe, to do so select “Wipe Data/Factory Restore” and confirm this action.

Step #16: Reboot your tablet.

That’s it, the Android 4.1.1 Jelly Bean is now installed on your Galaxy Tab Note 10.1, when you need to go back, once again install Android 4.0.4 firmware by repeating step 1 to step 10. Enjoy! If you faced any issue, do comment below.

Via: Sam MobileXDA

Recently Published

Best Deal Magazines

Digital Magazines in your Pocket

Reading is a great hobby to have. You can learn a lot of new things ...

24FX - Forex Trading App Review

24FX – Forex Trading App Review: An Amazingly Customized Trading App

Forex trading is a convenient investment option comparing to other ...

Get Live Market Updates - Anyoption App review

Get Live Market Updates – Anyoption App review

As technology is growing rapidly and Mobile devices have become ...

5 Best Casino or Gambling Apps

5 Best Casino or Gambling Apps

Choosing the 5 best casino or gambling apps is difficult even for the ...

Skin Care Tips in Urdu

The 10 Best Urdu Android Health Apps

Today, there’s some Urdu apps for just about your health issues. We ...

Jungle Adventures - free

Just Released Free Android Game Apps 2015

We are at play store for checking new and updated android game apps. ...

Samsung Netherland Says Galaxy Note 3 Neo Lollipop Update Is Coming

Samsung Netherland Says Galaxy Note 3 Neo Lollipop Update Is Coming

Samsung is busy in updating their devices to trending Lollipop ...

Galaxy S6 Active Listed On Samsung’s Official Website

Galaxy S6 Active Listed On Samsung’s Official Website

It is now possible that the Korean company will introduce the ...

Third Generation Moto E Name Appears On Flipkart

Third Generation Moto E Name Appears On Flipkart

The upcoming Motorola’s Moto E (third generation) is might be about ...